фф. Какая команда отображает информацию о настройке automdix для определенного интерфейса
Скачать 0.55 Mb.
|
A technician is configuring a new Cisco 2960 switch. What is the effect of issuing the BranchSw(config-if)# shutdown command? It disables a virtual or physical switch interface. It applies an IPv6 address to the virtual interface. It applies an IPv4 address to the virtual interface. It permits an IPv6 address to be configured on a switch physical interface. It updates the MAC address table for the associated port. A technician is configuring a new Cisco 2960 switch. What is the effect of issuing the BranchSw(config-if)# ipv6 address 2001:db8:a2b4:88::1/64 command? It applies an IPv6 address to the virtual interface. It activates a virtual or physical switch interface. It applies an IPv4 address to the virtual interface. It permits an IPv6 address to be configured on a switch physical interface. It updates the MAC address table for the associated port. A technician is configuring a new Cisco 2960 switch. What is the effect of issuing the BranchSw(config-if)# exit command? It returns to global configuration mode. It returns to privileged mode. It configures the default gateway for the switch. It enters user mode. It saves the startup configuration to the running configuration. A technician is configuring a new Cisco 2960 switch. What is the effect of issuing the BranchSw> enable command? It enters privileged mode. It enters the global configuration mode. It enters configuration mode for a switch virtual interface. It updates the MAC address table for the associated port. It permits an IPv6 address to be configured on a switch physical interface. A technician is configuring a new Cisco 2960 switch. What is the effect of issuing the BranchSw(config-if)# duplex full command? It allows data to flow in both directions at the same time on the interface. It allows data to flow in only one direction at a time on the interface It automatically adjusts the port to allow device connections to use either a straight-through or a crossover cable. It configures the switch as the default gateway. It encrypts user-mode passwords when users connect remotely. What type of VLAN should not carry voice and network management traffic? data VLAN voice VLAN management VLAN security VLAN What type of VLAN should not carry voice and network management traffic? data VLAN trunk VLAN security VLAN voice VLAN What type of VLAN is designed to reserve bandwidth to ensure IP Phone quality? voice VLAN trunk VLAN security VLAN management VLAN What type of VLAN is initially the management VLAN? default VLAN native VLAN data VLAN management VLAN What type of VLAN is designed to have a delay of less than 150 ms across the network? voice VLAN desirable VLAN trunk VLAN security VLAN What type of VLAN is used to separate the network into groups of users or devices? data VLAN management VLAN voice VLAN native VLAN What type of VLAN is configured specifically for network traffic such as SSH, Telnet, HTTPS, HHTP, and SNMP? management VLAN security VLAN trunk VLAN voice VLAN What type of VLAN is configured specifically for network traffic such as SSH, Telnet, HTTPS, HHTP, and SNMP? management VLAN voice VLAN security VLAN native VLAN What type of VLAN supports untagged traffic? native VLAN voice VLAN security VLAN management VLAN What type of VLAN supports untagged traffic? native VLAN desirable VLAN trunk VLAN security VLAN Refer to the exhibit. A network administrator has configured R1 as shown. When the administrator checks the status of the serial interface, the interface is shown as being administratively down. What additional command must be entered on the serial interface of R1 to bring the interface up? CCNA2 v7 SRWE – Modules 1 – 4: Switching Concepts, VLANs, and InterVLAN Routing Exam Answers 18 IPv6 enable clockrate 128000 end no shutdown
Refer to the exhibit. The network administrator wants to configure Switch1 to allow SSH connections and prohibit Telnet connections. How should the network administrator change the displayed configuration to satisfy the requirement? CCNA2 v7 SRWE – Modules 1 – 4: Switching Concepts, VLANs, and InterVLAN Routing Exam Answers 03 Use SSH version 1. Reconfigure the RSA key. Configure SSH on a different line. Modify the transport input command. Which solution would help a college alleviate network congestion due to collisions? a firewall that connects to two Internet providers a high port density switch a router with two Ethernet ports a router with three Ethernet ports
Which two statements are correct with respect to SVI inter-VLAN routing? (Choose two.) Switching packets is faster with SVI. There is no need for a connection to a router. Virtual interfaces support subinterfaces. SVIs can be bundled into EtherChannels. SVIs eliminate the need for a default gateway in the hosts.
Refer to the exhibit. A network administrator is configuring inter-VLAN routing on a network. For now, only one VLAN is being used, but more will be added soon. What is the missing parameter that is shown as the highlighted question mark in the graphic? CCNA2 v7 SRWE – Modules 1 – 4: Switching Concepts, VLANs, and InterVLAN Routing Exam Answers 16 It identifies the subinterface. It identifies the VLAN number. It identifies the native VLAN number. It identifies the type of encapsulation that is used. It identifies the number of hosts that are allowed on the interface.
Which type of VLAN is used to designate which traffic is untagged when crossing a trunk port? data default native management
A network administrator issues the show vlan brief command while troubleshooting a user support ticket. What output will be displayed? the VLAN assignment and membership for device MAC addresses the VLAN assignment and membership for all switch ports the VLAN assignment and trunking encapsulation the VLAN assignment and native VLAN
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question. Which message is displayed when 10.10.10.1 is entered into the PC1 Web Browser address bar? Local Server Test Server File Server Cisco Server
|