Английский. Учебное пособие для аудиторной и самостоятельной работы студентов III курсов ммф йошкарОла пгту 2013 удк 811. 111 (07)
 Скачать 0.72 Mb.
|
|
Запомните необходимый минимум профессиональной лексики:
Задание II 1. Определите по формальным признакам, какой частью речи являются следующие слова, и переведите их: Electrically, lubrication, continuous, variety, numerical, circular, circumference, movement, slowness, simultaneous 2. Определите значения суффиксов и префиксов в следующих словах и переведите их: Interchangeable, ultrasound, cutter, portable, multispindle, displacement, holder, unimportant Задание III 1. Подберите эквиваленты к глаголам, обозначенным цифрами:
2. Подберите эквиваленты к словосочетаниям, обозначенным цифрами:
3. Подберите подходящую пару к словам, обозначенным цифрами. Полученные словосочетания переведите.
4. Соотнесите термины с их определениями:
Задание IV
Задание V
2. Определите, какие из данных утверждений истинны, а какие ложны:
3. Ответьте на вопросы к тексту:
2. What hand tools were replaced by machine tools? 3. What the functions of a milling machine? 4. What is the difference between shapers and planers? 5. How is grinding carried out? Задание VI 1. Выполните письменный перевод текста. 2. Выполните устный пересказ текста, используя необходимые фразы. Unit 9
Recrystallization, extrusion, operation, diameter, critical, complex, limit
METALWORKING PROCESSES Metals are important in industry because they can be easily deformed into useful shapes. A lot of metalworking processes have been developed for certain applications. They can be divided into five broad groups: rolling, extrusion, drawing, forging, sheet-metal forming. During the first four processes metal is subjected to large amount of strain (deformation). But if deformation goes at a high temperature, the metal will recrystallize – that is, new strain-free grains will grow instead of deformed grains. For this reason metals are usually rolled, extruded, drawn, or forged above their recrystallization temperature. This is called hot working. Under these conditions there is no limit to the compressive plastic strain to which the metal can be subjected. Other processes are performed below the recrystallization temperature. These are called cold working. Cold working hardens metal and makes the part stronger. However, there is a limit to the strain before a cold part cracks. Rolling is the most common metalworking process. More than 90 percent of the aluminum, steel and copper produced are rolled at least once in the course of production. The most common rolled product is sheet. Rolling can be done either hot or cold. If the rolling is finished cold, the surface will be smoother and the product stronger. Extrusion is pushing the billet to flow through the orifice of a die. Products may have either a simple or a complex cross section. Aluminum window frames are the examples of complex extrusion. Tubes or other hollow parts can also be extruded. The initial piece is a thick-walled tube, and the extruded part is shaped between a die on the outside of tube and a mandrel held on the inside. In impact extrusion (also called back-extrusion) the workpiece is placed in the bottom of a hole and a loosely fitting ram is pushed against it. The ram forces the metal to flow back around it, with the gap between the ram and the die determining the wall thickness. The example of this process is the manufacturing of aluminum beer cans. Drawing consists of pulling metal through a die. One type is wire drawing. The diameter reduction that can be achieved in one die is limited, but several dies in series can be used to get the desired reduction. Forging is the shaping of a piece of metal by pushing with open or close dies. It is usually done hot in order to reduce the required force and increase the metal’s plasticity. Open-die forging is usually done by hammering a part between two flat faces. It is used to make parts that are too big to be formed in a closed die or in cases where only a few parts are to be made. The earliest forging machines lifted a large hammer that was then dropped on the workpiece, but now air or steam hammers are used, since they allow greater control over the force and the rate of forming. The part is shaped by moving or turning it between blows. Closed-die forging is the shaping of hot metal within the walls of two dies that come together to enclose the workpiece on all sides. Sheet metal forming is widely used when parts of certain shape and size are needed. It includes forging, bending and shearing. One characteristic of sheet metal forming is that the thickness of the sheet changes little in processing. The metal is stretched just beyond its yield point (2 to 4 percent strain) in order to retain the new shape. Bending can be done by pressing between two dies. Shearing is a cutting operation similar to that used for cloth. Each of these processes may be used alone, but often all three are used on one part. For example, to make the roof of an automobile from a flat sheet, the edges are gripped and the pieces pulled in tension over a lower die. Next an upper die is pressed over the top, finishing the forming operation, and finally the edges are sheared off to give the final dimensions. Heat treatment Metals can be heat treated to alter the properties of strength, ductility, toughness, hardness or resistance to corrosion. Common heat treatment processes include annealing, normalization, quenching and tempering. Heat treatment of metals Metals undergo heat treatment to improve its structure and to obtain higher or specified mechanical properties. The types of heat treatment applied in practice are: (1) annealing, (2) normalization, (3) quenching and (4) tempering. Heat treatment is the process of controlled heating and cooling of metals to change their structural arrangement and to ensure certain desirable properties. Annealing consists of heating the metal to a temperature slightly above the critical temperature and then cooling slowly to produce an even grain structure, reduce the hardness, and increase the ductility. Normalizing is a form of annealing in which the material is cooled in the air. Quenching or rapid cooling from above the critical temperature by immersion in cold water or some other cooling medium, is a hardening treatment. Tempering consists of reheating the quenched metal to restore ductility to some extent and reduce the brittleness.
Задание II
Compressive, condition, loosely, normalization, desirable, slightly, immersion
Recrystallize, deformed, enclose, thickness, reheat, restore Задание III 1. Подберите эквиваленты к глаголам, обозначенным цифрами:
|